omv8:armbian_trixie_install [omv-extras.org]

This page is read only. You can view the source, but not change it. Ask your administrator if you think this is wrong.
{{indexmenu_n>3}}

<html><!---
Remark: Given the similar setup, this doc contains numerous reused screen shots from previous installation documents.
---></html>

<html><center><span style="color:#000066;font-size:300%;">Installing OMV8 on Armbian Trixie</span></center></html>

{{ :omv8-splash.jpg?nolink&600 |}}
\\
====== Installing OMV8 on Armbian Trixie ======


Draft.\\
\\
Revisions: N/A\\

\\




===== Introduction =====

This guide applies to Single Board Computers (SBC's) //other// than the Raspberry PI.  Due to the lack of the numerous SBC's that would be required for testing and integration, providing pre-built images for all Armbian supported SBC's, with Openmediavault (OMV) installed, is not possible.   
However, installing OMV8 on Armbian supported SBC's is a relatively easy task.  This document is a guide for that purpose.


===== About this Guide =====

The purpose and intent of this guide is to provide a walk-through to get SBC users up and running as quickly and as easily as possible.  This guide assumes that users have a working Windows Client for installing and executing the needed utilities.  It is also assumed that Mac and Linux desktop users will be able to find, install, and use utilities equivalent to those called out in Prerequisites.

  * This guide contains links to external sources of information and software.  It's best used on an Internet connected PC.
  * This is a community document and a work in progress.  Input and feedback are welcome and can be sent to: [[omvguide@gmail.com]]
\\
<html>
<body>
  <table width="100%" border="0">
    <tr>
      <td colspan="2" style="background-color:#69A5FF;height:30px;">
        <strong><span style="color:#FFFFFF;font-size:110%;">&#160; FOREWORD</span></strong>
      </td>
    </tr>
    <tr>
      <td style="background-color:#E6FEFF;height:25px;width:380px;">
        This guide was written to avoid as many installation pitfalls as is possible to anticipate or predict.  With that in mind, please adhere to this guide without deviating in any significant way.  Specifically, that means DO NOT preconfigure wireless networking (that will be covered later - after OMV is installed), or use armbian-config prior to the installation of OMV.  Once the OMV installation is complete, and after backing the OS' SD-card → <a href="https://wiki.omv-extras.org/doku.php?id=omv7:utilities_maint_backup#cloning_flash_media" target="_blank">Cloning Flash Media</a>, additional configuration or experimentation will be possible without losing the install, if something goes awry. 
    </tr>
  </table>
</body>
</html>
((Update Link when Util's and Maint for OMV8 is done.))






===== Supported Devices =====

Given the wide variety of Armbian supported devices, and the images available for these devices, it's important to understand what will and will not work with an Openmediavault 7 installation.\\
\\
**OMV8** will install on most SBC devices with Armbian support __AND__ a **Debian 13 __Trixie__** image.\\
\\
Further, before selecting a Trixie image, note that Armbian supports devices with differing levels of support.  See -> [[https://docs.armbian.com/User-Guide_Board-Support-Rules/|this page]] for an explanation of the different support levels.  Devices with "Standard support" or "Community support" images are acceptable.  While **Staging - Work in progress** images may work, they are not supported and are used at the users risk. 

A list of images, for your particular SBC can be found on the -> [[https://www.armbian.com/download/|Armbian Download Page]].  Find your SBC on the download page, click it, and scroll down to the "Branded" images as shown below.  Select **Trixie Minimal/IOT** or **Trixie CLI** images only.\\
\\
\\
===== Not Supported =====
  * Any **Desktop** image.
  * Any **Ubuntu** image.
  * **Jammy**, **Debian 12 - Bookworm**, **Debian 12 - SID** or other **non-Trixie variants** are **not supported**.
  * Images at the bottom of some device pages under the heading of "**Rolling releases from CI pipeline**" are **not supported**.
  * **Dedicated** images at the very bottom of some device pages.
  * SBC's that have 32-bit CPU's or that Armbian supports with a 32-bit userland.  See the -> [[https://wiki.omv-extras.org/doku.php?id=omv8:omv8_compatibility|OMV8 Compatibility Doc]] for details.\\
\\

----
===== Prerequisites =====


This installation process __requires__ a wired Ethernet connection and Internet access.
Typically, all that is needed to begin the installation is an Ethernet cable, an Armbian supported SBC, a power supply sufficient for the SBC model being used, and one SD-card (two are preferred for backup).\\
\\
<html>
<body>
  <table width="100%" border="0">
    <tr>
      <td colspan="2" style="background-color:#69A5FF;height:30px;">
        <strong><span style="color:#FFFFFF;font-size:110%;">&#160; Note</span></strong>
      </td>
    </tr>
    <tr>
      <td style="background-color:#E6FEFF;height:25px;width:380px;">
For best results, please <b>DO NOT</b> vary from the process outlined.<br>  
Examples of variation would be "preconfiguring wireless networking" or the installation of extra packages <i><b>before</b></i> running the installation script.<br>
    </tr>
  </table>
</body>
</html>
\\
To get started, a few utilities are needed to expand, check, and work with an Armbian image.

  * To check the decompressed image, an [[https://md5-sha-checksum-utility.en.lo4d.com/windows|MD5 – SHA Checksum utility]] is needed.  This utility is portable, meaning it's not necessary to install it, but it may require support files.  Simply run the executable.
  * [[https://www.sdcard.org/downloads/formatter/index.html|SDformatter]] is a utility for formatting SD-cards, that does a trim operation on flash media to clear remnants of old files. SDformatter is installable on a Windows client.   
  * [[http://www.heise.de/ct/Redaktion/bo/downloads/h2testw_1.4.zip|h2testw_1.4]] is a flash media test program.  With a freshly formatted SD-card or USB thumbdrive, it writes files with known content and verifies the content in a read operation, detecting errors in the process.  **h2testw_1.4** downloads as a zip file.  By right clicking on the zip file, and using “Extract All”, 7-Zip will expand the zip file to a folder named **h2testw_1.4**  The executable inside this folder is a portable application. Run the executable. 
  * To burn an Armbian Bullseye image to an SD-card, [[https://gitlab.com/bztsrc/usbimager/raw/binaries/usbimager_1.0.8-i686-win-gdi.zip|USBimager]] is recommended.  (It burns the image and verifies it in one process.)  USBimager for Windows is portable, with no required installation.  Extract the archive with 7zip and use the executable file (usbimager.exe)
  * [[https://www.chiark.greenend.org.uk/~sgtatham/putty/latest.html|PuTTY]] is an SSH client that will allow users to connect to their SBC, from a Windows client, and get on the command line.  PuTTY is installable on a Windows client. 
  * While 8GB is the minimum, a 16GB card will provide longer life in the role of a boot drive.  Users are encouraged to get two SD-cards.  One is for the installation and the second is for backing up the OS installation, when configuration is complete.  


For the best experience, use only high quality **__new__** SD-cards, such as Samsung or SanDisk, that are rated A1 Class 10 or better.

{{ :armbian1_sd-card.jpg?80 |}}



{{ :divider2.png?800 |}}






===== Working With the Image File =====

- Download the appropriate (Debian Trixie) image for your SBC.  -> [[https://www.armbian.com/download/|Armbian Download Page]].\\
- Download the associated SHA file to confirm the image.  (This document will contain the SHA hash.)\\

\\



==== Verify the image ====
 
MD5 and SHA hashes check for image corruption that may have occurred during the download.  

<html>
<body>
  <table width="100%" border="0">
    <tr>
      <td colspan="2" style="background-color:#69A5FF;height:30px;">
        <b><span style="color:#FFFFFF;font-size:110%;">&#160; Beginners Note - DO NOT SKIP THIS STEP</span></b>
      </td>
    </tr>
    <tr>
      <td style="background-color:#E6FEFF;height:25px;width:380px;">
        <p>The chance of image corruption is highest when downloading and it's pointless to build a server with flawed software.  Even the slightest corruption of the image may ruin your installation and the effects may not be noticed until well after your server is built and in use.  Headaches can be avoided by checking the image.
</p>
    </tr>
  </table>
</body>
</html> 

{{ :divider2.png?800 |}}
Verify the image file, for your SBC, with the [[https://md5-sha-checksum-utility.en.lo4d.com/windows|MD5 & SHA checksum utility]].  

(Note that it's possible to “drag and drop” the image file name into the utility, on the **File** line.  Otherwise, use the **Browse** button and navigate to the image file.)

{{ ::omv7-arm-03.jpg?700 |}}

\\ 
\\ 
----
(If the file was not downloaded:)\\
Click the SHA link that's associated with the image downloaded.  A text file may download or a SHA256 hash may be displayed in the browser.\\

Notepad can be used to view the downloaded the sha256 hash or, if viewed from Armbian's web
site, simply paste the hash directly into the bottom "**Hash**" line (above) and click on **verify**.\\
\\
<html><center>(In this case, from a downloaded hash file, the first line is the sha256 hash.)</center></html>

{{ :omv7-arm-04.jpg?600 |}}

<html><center>With a SHA-256 match, the downloaded image is verified.</center></html>



\\ 
  
==== Format and Test Flash Media ====


Using SDFormatter, do a clean format:

(Note that SDFormatter does a trim operation on the card which cleans up remnants of deleted or previously existing files.)  

In most cases, SDFormatter will detect the SD-card or thumb-drive.  A volume label is not necessary, at this point, and the default options are fine.

{{ :omv6-rpi-4.jpg?400 |}}
\\ 
\\ 
----

<html><center>After the SD-card format is completed, open <strong>h2testw</strong> and select your language.</center></html>
<html><center>Then, click on <strong>Select target</strong></center></html>


{{ :omv6-rpi-5.jpg?400 |}}
\\ 
\\
----

<html><center>Under <strong>Computer</strong>, select the flash media previously formatted.</center></html>


{{ :omv6-rpi-6.jpg?400 |}}
\\ 
\\ 
----
  
<html><center><strong>Select Write+Verify</strong>.  (Do not check the endless verify box).</center></html>


{{ :omv6-rpi-7.jpg?400 |}}
\\ 
\\ 
----
<html><center>A dialog similar to the following may pop up, highlighting a 1MB difference.</center></html>  
<html><center>Ignore it and click on <strong>OK</strong>.</center></html>

{{ ::armbian10_h2testw_warning.jpg?400 |}}

\\ 
\\ 
----

<html><center>“<strong>Without errors</strong>” is the desired outcome.  If the media tests with errors or is much smaller than is indicated by the SD-card's labeled size, don't use it.</center></html>


{{ :omv6-rpi-8.jpg?400 |}}

After H2testw verifies the SD-card; **do one more clean format**, using **SDFormatter**, before flashing the card.  While optional, at this point, a volume label could be applied.

\\ 
\\ 
  
==== Flashing Armbian onto an SD-card ====


<html><center><strong>Start USBImager:</strong></center></html>

<html><center>Click on the highlighted file selector box: </center></html>
<html><center>Navigate to the downloaded image, select it and open the compressed image to be flashed.</center></html>

{{ :omv8:omv8-arm-05.jpg?nolink&400 |}}

----

<html><center>Using the drop down select the SD-card.</center></html>
<html><center>The <strong>verify</strong> box should be checked.</center></html>

{{ :omv8:omv8-arm-06.jpg?nolink&400 |}}

----

<html><center>Click the <strong>Write</strong> button to flash the image.</center></html>

{{ :omv8:omv8-arm-07.jpg?nolink&400 |}}


----

<html><center>USBImager will write and verify the image.</center></html>

{{ :omv8:omv8-arm-08.jpg?nolink&400 |}}
----


===== The First Boot =====

*At this point, a wired Ethernet connection is required to connect to the SBC with PuTTY and to install OMV in a later process.*

  * Insure the SBC is connect to wired Ethernet.  
  * Insert the SD-card, into the SBC, and apply power. 
  * Wait 3 to 5 minutes. 

The IP address to use for logging into the console is available from your DHCP server.  In most cases, your DHCP server will be running on your LAN's router.

(The following is an example.)

{{ ::omv6-arm-07.jpg?800 |}}


With the IP address noted, proceed to **First Time Login**.

{{ :divider2.png?600 |  |}}

<html><center><strong>If there's a problem with obtaining a DHCP assigned IP address:</strong></center></html>

  * In the event that an IP address is not issued to your SBC, check the wired Ethernet connection and reboot the device.  In some cases this will mean unplugging and plugging the power supply back in.  Allow time for boot up (5 minutes or so) and check the DHCP server again.
  * If an address is not issued, or if the user doesn't know how to find the ARM device's IP address on their DHCP server, connect a monitor and keyboard to watch the boot process until it completes.  If the IP address is not displayed at the end of the boot cycle, login with the user **root** and password **1234** 
Unfortunately, this first time logon will start a mandatory root user password change and the addition of a non-root user.  Once these processes are complete, type ''ip add'' on the command line.  Note the IP address of the Ethernet interface, in the output, and proceed to First Time Login.
  * In rare instances, it may be necessary to reboot the LAN's router, followed by rebooting the SBC.


{{ :divider2.png?600 |}}

===== Armbian - First Time Logon =====

<html><center><strong>Open PuTTY and type in the OMV IP address</strong></center></html>


{{ :wiki:omv6-arm-08.jpg?400 |}}
----


<html><center>A PuTTY <b>Security Alert</b> will pop up in a first time connection.</center></html>
\\  
<html><center>This is normal.  Ignore it and select <strong>Yes</strong>.</center></html> 

\\
\\
----

<html><center><b>When the SSH window opens:</b></center></html>
\\
<html><center>Login as: <mark><b>root</b></mark>    The Armbian default password is: <mark><b>1234</b></mark></center></html> 
\\
<html><center>After logging in with the default password, you'll be required to change the root password.</center></html> 
<html><center>Follow the prompts to enter and confirm a new root password. (Remember this password.)</center></html>

{{ ::omv6-arm-09.jpg?600 |}}
----

\\

<html><center><b>Armbian will prompt for additional settings:</b></center></html>
\\
  * **Create default system command shell**: Beginners should use **bash**.
  * **Create a new user account**:  If completed, this dialog creates a non-root user, with “sudo” admin abilities.  While this user is optional, note that the user name **can not** be "**admin**".  ''Ctrl+C'' exits user creation.

{{ ::omv6-arm-10.jpg?600 |}}

-----

<html><center><b>Developer images:</b></center></html>
<html><center>Note the text in the following.</center></html>

{{ :omv8:omv8-arm-09.jpg?nolink&600 |}}

Unfortunately, while images of this type usually work, given what they are, they're **not officially supported**.\\
In times past, the Armbian project clearly labeled Developer images in their download pages.  Recently, it appears that this is no longer the case so login prompts of this type are the first warning.

Again, while images of this type not supported:\\
If users carefully back up their OS drive (usually an SD-card) before applying OS or OMV updates, and maintain boot drive backup, it will be possible to back out of potential issues.  -> Cloning Flash Media.  ((Update to OMV8 - Utilities when complete.))

\\
----





===== Finishing the Armbian Install =====


On the command line, copy and paste the following commands, one at a time, into the SSH window:

''apt-get update''  

''apt-get upgrade -y''

(The above command may take a few to several minutes to complete.)

''wget -O - https://github.com/OpenMediaVault-Plugin-Developers/installScript/raw/master/preinstall | sudo bash''

Finally, reboot the SBC with the following command:

''reboot''\\
\\
**Note:**\\
Some devices may require a hard power off and on, to reboot.  In such cases, physically remove and reconnect power.\\
\\
In a few minutes, open a new PuTTY/SSH window for the installation of OMV.\\
\\
*In the event that the SSH client does not respond to the IP address used for the Armbian installation, look at your DHCP server again to see if a “new” IP address has been assigned.*

\\ 
  
===== Install OMV =====



Installing OMV on Armbian is very easy, thanks to Arron Murray (ryecoaaron on the [[https://forum.openmediavault.org/|OMV Forum]]) for providing a comprehensive installation script that's executed from a single line. \\
\\

Highlight and copy the following line complete (**Ctrl+C**) and paste it into PuTTY's SSH window, with a right mouse click.  Then hit **Enter**.

''wget -O - https://github.com/OpenMediaVault-Plugin-Developers/installScript/raw/master/install | sudo bash''\\
\\

Once the script is running, click out of the SSH window so the script will not be interrupted.
**Note: Do Not Close PuTTY** – that will terminate the root session.  Minimizing PuTTY is OK, but it must be running. 
     
Depending on several factors, running this script may take up to 30 minutes.

When the script is complete, the SBC will automatically reboot.

\\ 
  
==== First Time GUI Logon ====

After 3 to 5 minutes, OMV can be logged in using the same IP address that was used for the SSH client, entered in a web browser address bar.   The web GUI user is **admin** and the default password is **openmediavault**

Users may be prompted with a **yellow banner** to accept **pending configuration changes**.  Click the check mark to **accept**.\\

\\ 
**Note** - after the completion of the script:

In the rare event that the OMV console or SSH client does not respond to the IP address used during the installation, recheck  your DHCP server to see if a “new” IP address has been assigned.

(Typically, consumer router DHCP leases last at least 24 hours.  In cases where DHCP leases are very short - as it is with some versions of DD-WRT router firmware [10 minutes] - the lease issued to the SBC may time out at the end of the installation.  A different address may be issued on reboot.)

\\ 
  
===== Finishing Up =====

  * **To add an existing or add-on Wireless Interface** to openmediavault, see [[https://wiki.omv-extras.org/doku.php?id=omv8:armbian_trixie_install#final_notes|Final Notes]] below.
  * New users can continue with the setup of OMV using the [[https://wiki.omv-extras.org/doku.php?id=omv8:new_user_guide|Getting Started with Openmediavault 8]] guide, starting in the section titled → [[https://wiki.omv-extras.org/doku.php?id=omv8:new_user_guide#initial_configuration|Initial Configuration]].
  * All users are encouraged to review this resource → [[https://wiki.omv-extras.org/doku.php?id=omv7:utilities_maint_backup|Utilities, Maintenance & Backup]]  ((Reset link after OMV8 Utilities is complete.)) for an easy process to clone your SBC's SD-Card and for additional information that will help in managing and maintaining an openmediavault server.






  
===== Final Notes: =====





==== Wireless Networking ====

First it should be noted that using a wireless interface, with a server, is not the best idea.  To prevent a 
number of issues such as interference, bandwidth contention issues with clients, etc., a server should be 
connected to the **wired** LAN ports of a router or a network switch.  However it is understood that, in some 
cases, wired connections may not be an option.

If your SBC is equipped with a wireless interface, by default, OMV will not show it in the GUI but it can be added. 
  * An existing interface can be added as noted in the following.
  * After plugging it in, a compatible add-on USB wireless interface can be added in the same manner.
\\

<html><center>Under <b>Network</b>, in the <b>Interfaces</b> tab, click on the <b>+ Add</b> button.  From the pop up, select <b>Wi-Fi</b>.</center></html>
\\
{{ ::omv6-arm-11.jpg?800 |}}
\\ 
----
\\
<html><center>In the <b>Create window</b>, select the drop down arrow next to the <b>Device</b> field.</center></html>
<html><center>The on-board or add-on wireless interface will be the only interface in the list. Select it.</center></html>
\\
<html><center>In the <b>SSID</b> field, enter the SSID for the wireless network.</center></html>
<html><center>In the <b>Password</b> field, enter the WiFi encryption password.</center></html>
<html><center>Under <b>IPv4</b>, in the <b>Method</b> field, click on the drop down arrow and select <b>DHCP</b> or statically address as needed.</center></html>
\\  







{{ :omv6-arm-12.jpg?800 |}}

<html><center>Scroll down and click, <strong>Save</strong>.</center></html>
\\
At this point, the wireless interface will appear under **Network**, in the **Interfaces** window.  
Further configuration can be done, as needed, by clicking on the interface line and the edit button (pencil).\\
\\ 
To further configure the SBC; refer to the [[https://wiki.omv-extras.org/doku.php?id=omv8:new_user_guide|Getting Started with Openmediavault 8]], starting in the section titled [[https://wiki.omv-extras.org/doku.php?id=omv8:new_user_guide#initial_configuration|Initial Configuration]].

{{ :divider2.png?800 |}}

===== A Closing Note =====

We, who support the openmediavault project, hope that you’ll find your openmediavault server to be 
enjoyable, efficient, and easy to use.\\
If you found this guide to be helpful, please consider a modest donation to support the 
hosting costs of this server. \\

\\

**OMV-Extras.org**
\\
<html>
<form action="https://www.paypal.com/cgi-bin/webscr" method="post" target="_top">
<input type="hidden" name="cmd" value="_s-xclick">
<input type="hidden" name="hosted_button_id" value="2BQNGSC8HQJME">
<input type="image" src="https://www.paypalobjects.com/en_US/i/btn/btn_donate_SM.gif" name="submit" title="PayPal - The safer, easier way to pay online!" alt="Donate with PayPal button" border="0">
<img alt="" src="https://www.paypal.com/en_US/i/scr/pixel.gif" width="1" height="1" border="0">
</form>
</html>
\\
\\
**Venmo: ryecoaaron** \\